Cart: 0 item(s) - £0.00

Hardwax Oil Clear

Hardwax Oil Clear
Protect and enhance the natural beauty of wood with Treatex Hardwax Oil. Using over 40 years of experience in the timber and wood finishing industries our Hardwax Oil was developed to be user friendly, quick drying, easy to maintain and above all to provide a hard wearing and attractive finish.
Stock Status : In Stock
Product Code : treatex-hardwaxoilclear-mt-0.5lt
Product Brand : Treatex
Product Condition:   New
Please Choose Size
Please Choose Sheen
£14.36
£17.26
Send to a friend

Features

  • Comes in Matt, Satin or Gloss sheen levels
  • Has a warming effect on lighter coloured timbers
  • No sanding required between coats
  • Withstands high temperatures
  • Very durable
  • Easy to maintain with Treatex Wax Polish
  • Spot repairable
  • R10 slip resistance certified and slip resistant certified for commercial use: 
  • Complies with regulation DIN 68861-1B: Resistance to spills of water, wine, beer, coffee, tea, fizzy drinks etc
  • Safe for use on children’s toys: 
  • Meets with VOC emissions regulations
  • Recommended for those with dust allergies; dirt and dust can be removed easily
  • Easy to apply
  • Quick drying
  • Low odour
  • Water resistant
  • Very durable
  • Easy to clean with Treatex Floor Care or Treatex Spray on Floor and Surface Clean

Usage

Suitable for: internal use

Recommended timbers: All (dense/oily timbers may require Treatex Thinner)

Applications: floors, doors, stairs, worktops, woodturning etc.


Please Note! 
Clear Hardwax Oil must always be used as the final coat when Natural Hardwax Oil or Colour Tones are applied*


Coverage

1L will cover approximately 20m² in one coat depending on the timber and method of application.
2.5L will cover approximately 50m² in one coat depending on the timber and method of application.
2.5L will cover approximately 30m² in two coats depending on the timber and method of application.
1L will cover approximately 3 doors in two coats depending on the timber and method of application.


Preparation

If the surface to be treated is rough or if a previous surface coating finish (e.g. varnish, lacquer, etc.) is present, sand to smooth bare wood with 80-120 grit sandpaper. Some previously oiled surfaces can be overcoated, without sanding. To check compatibility, a trial application is essential when overcoating a previously oiled surface. Remove dust, dirt and any other contaminates which may lead to uneven absorption of Clear Hardwax Oil. Make sure the surface to be treated is thoroughly dry. Stir tins and ensure product is at room temperature before use. Enough product should be purchased to complete the whole project and when more than one container is required it is advisable to mix them together before use. We strongly recommend a small trial application prior to starting a project.

Application

If you are treating oily/dense timbers e.g. Iroko, Ipe, Teak, Jarrah, Merbau etc. thin the first coat of Treatex Hardwax Oil Clear by mixing with approximately 10% Treatex Thinner. This enables the product to properly penetrate into these types of timbers. Use a brush or roller to evenly apply Treatex Hardwax Oil allowing roughly 30g per m². On worktops and doors etc. pay particular attention to end grain (on end grain apply wet on wet until product is no longer absorbed by the wood). Allow to dry – maintaining warmth and ventilation will enable the surface to dry within 3-6 hours. Apply with a brush or roller a second coat of Treatex Hardwax Oil, again allowing roughly 30g per m². Allow to dry thoroughly overnight before the surface is lightly used. The surface will reach maximum hardness after a further 24 hours.

 

 

Tips

If Treatex Hardwax Oil is applied too thickly, drying time will be increased. To speed up drying time raise the room temperature and increase air flow by opening doors and windows, or using a fan. 

Treatex brushes and rollers are available. Alternatively, use a short gloss pile roller or good quality brush. Tightly wrap a plastic bag around wet rollers and brushes to stop them drying out between coats. Wet brushes and rollers can be cleaned using white spirit. If you are using hardener then wet rollers and brushes will dry even if they are wrapped in a plastic bag and it will not be possible to clean them.

 


Material Safety Data Sheet
Clear Matt Clear Satin
Clear Gloss


Write an online review and share your thoughts with other shoppers!

Be the first to review this product